Snowflake #34 Ornament Pattern
Sandra D. Halpenny ©
2007 – 2010 All rights reserved
www.SandraDHalpenny.com
S = Miyuki® 11/0 seed beads, 247 beads
Start by waxing and stretching your thread. Use C-lon beading thread, Fireline*, or Nymo D and an #11 or #12 beading needle. Tie in a “stopper” bead, leaving about a 8-10” tail and begin at step #1.
Round 1
Pick up 6S, make a circle and go with thread through the 1st S bead just added. Continue with working thread around through all 6 beads again, plus go through the 1st bead again. Circle of 6 made, (C6).
Round 2
a) Pick up 12S, go with thread down through the 5th through 1st S beads just added in this step and forward (right to left) through the next S bead in C6.
b) Repeat (a), around 5 more times
c) Continue with working thread forward through the 1st through 8th S beads in the first repeat of (a) this Round.
Round 3
a) Pick up 3S, go with thread down through the 10th, 11th, and 12th S beads, R2a.
b) Pick up 5S, go with thread up through the 6th, 7th and 8th S beads in the next repeat of (a), R2.
c) Repeat (a and b) around 5 more times.
d) Continue with working thread up through the 1st S bead in the first repeat of (a) this Round.
Round 4
a) Pick up 5S, go with thread down through the 3rd S bead, R3a, the 10th and 11th S beads, R2a.
b) Pick up 6S, go with thread up through the 7th and 8th S beads in the next repeat of (a), R2, and the 1st S bead, R3a.
c) Repeat (a and b) around 5 more times.
d) Continue with working thread forward through the 1st and 2nd S beads in the first repeat of (a) this Round.
Snowflake Pattern Steps 2-4
Round 5
a) Pick up 3S, go with thread down through the 4th and 5th S beads, R4a.
b) Pick up 3S, go with thread left to right through the 3rd and 4th S beads, R4b.
c) Pick up 3S, go with thread up thrugh the 1st and 2nd S beads in the next repeat of (a), R4.
d) Repeat (a, b and c) around 5 more times.
e) Weave the working thread into the snowflake and end.
Snowflake Step 5
Bead colors for Rounds
R = Round
Each Round begins at the red dot in drawing. The snowflakes are done in rounds.
Snowflake Tips
Making Hangers for your Snowflake
1. Make it with beads, make a loop with as many beads as you would like,
2. or use a piece of fishing line, making it invisible with monofilament,
3. or a piece of pretty ribbon. Add ribbon after your snowflake is stiffened.
Finishing
After the snowflake is complete, you can stiffen it with Future® Floor Finish. It is a great stiffener; it stays clear even on the crystals. Test it first if you use seed beads with dyed colors to make sure the floor finish doesn’t remove the colors.
Pour enough of the finish into a small container that is wide enough for the ornament. Float the ornament into the Future and push it around a bit with your finger. (After I am done with the floor finish, I use a funnel and pour the extra back into the bottle). Take the ornament out and blot both sides with a paper towel.
Put the ornament on a piece of wax paper, shape and flatten it and let it remain on the wax paper to dry. (If you use plastic wrap, the beads can stick a bit to the wrap, so it needs to be moved around a bit to prevent this from happening.) If your ornament needs a little extra flattening, use two pieces of wax paper and sandwich your ornament in between; put a book on top of the wax paper for about an hour. Take the book and the top piece of wax paper off the ornament and let dry overnight on the bottom piece of wax paper.
See more beautiful patterns at Sandra’s website – www.SandraDHalpenny.com